Edge Series
Easy to install invisible loudspeaker for drywall,
giving incredible bass extension and maximum SP
Edge Series
The latest innovation in invisible speaker technology
A new revolutionary design for invisible loudspeaker technology, the Amina Edge offers smooth low frequency extension with increased power handling and sensitivity, resulting in a dynamic and engaging listening experience that has never before been heard from an invisible loudspeaker.
Building on the incredible performance of the Mobius Series, Amina Edge loudspeakers incorporate OptiDamping, OptiDrive and Reduced-Resonance Exciter technology, built into a plaster up-to design. Designed for use where there is no wet plaster skim (drywall), Edge loudspeakers have been designed much like a piece of tapered-edge plasterboard. Once filled, taped and painted, the loudspeaker becomes fully invisible. Amina Edge speakers can also be installed as post-plaster product (retrofit) where there is a full wet skim (Edge speakers should not be fully plastered over).
Edge7
Inside Edge7
The Amina Edge7 offers smooth low frequency extension with increased power handling and sensitivity, resulting in a dynamic and engaging listening experience that has never before been heard from an invisible loudspeaker. Building on the award-winning Mobius Series design, the Edge7 incorporates OptiDamping, OptiDrive and Reduced-Resonance Exciter technologies, built into a plaster up-to design.
The Edge Soundboard
The speaker uses a high quality fire-resistant panel material which allows for seamless integration into plasterboard walls and ceilings without the need for a full wet skim, all in the easy to install, lightweight form-factor that Amina is known for.
Amina Tip:
Plaster up-to refers to the installation method and how the loudspeaker becomes invisible once installed. Edge speakers are installed much like a section of tapered-edge plasterboard, with the perimeter filled, taped and then fully painted over. When installed in this way, the loudspeaker becomes fully invisible, much like our plaster-over loudspeakers, but without the requirement for a full wet plaster skim.
Support Products
The Backbox CV345 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission.
Note: Edge loudspeakers not compatible with solid-wall installation.
All new slim-line design, giving reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack. Please note that Edge speakers require the ‘C’ variant single channel protection unit – for example for Edge7, use APUi70C.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Edge Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation. Please note that Edge speakers require the ‘C’ variant of protection unit, for example APU-RS16iC.
Specification | Edge7 |
Nominal Impedance | 4 Ohms |
Power Handling | 75W/150W |
Sensitivity | 93dB 1m/2.83Vrms (APUi70C connected) |
Frequency Response | 45Hz - 20kHz (±6db) mounted in Backbox CV345 |
Electrical Connection | Blue butt-splice crimp terminals (14-16 AWG) |
Dimensions | 450mm x 345mm x 31mm (173/4” x 135/8” x 11/4”) |
Product Weight | 1.78Kg (3lbs 15oz) |
Fixing Requirements | BackboxCV345 |
In-line Protection unit | APUi70C |
Rack-Mount Protection Unit | APU-RS8iC or APU-RS16iC |
Warranty | 10 Years Residential (5 Years Commercial) |
Datasheet | Edge7 Datasheet |
Datasheet | Install Guide | Images | CAD |
Edge7 Datasheet | Edge Install Guide | Edge7 Front | Edge7 DWG |
Edge7 Rear |
Edge5
Inside Edge5
The Amina Edge5 offers smooth low frequency extension and increased low-mid performance, resulting in a dynamic and engaging listening experience that has never before been heard from an invisible loudspeaker. Building on the award-winning Mobius Series design, the Edge5 incorporates OptiDamping and Reduced-Resonance Exciter technology built into a plaster up-to design.
The Edge Soundboard
The speaker uses a high quality fire-resistant panel material which allows for seamless integration into plasterboard walls and ceilings without the need for a full wet skim, all in the easy to install, lightweight form-factor that Amina is known for.
Amina Tip:
Edge Series speakers are designed to be installed into walls and ceilings where there is to be no wet plaster skim, however it is still possible to install the speaker where there are such finishes, but please note that you will need to install the speaker post-plastering and use alignment shims to achieve the correct finish.
Support Products
The Backbox CV345 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission.
Note: Edge loudspeakers not compatible with solid-wall installation.
All new slim-line design, giving reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack. Please note that Edge speakers require the ‘C’ variant single channel protection unit – for example for Edge5, use APUi50C.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Edge Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation. Please note that Edge speakers require the ‘C’ variant of protection unit, for example APU-RS16iC.
Specification | Edge5 |
Nominal Impedance | 8 Ohms |
Power Handling | 50W/100W |
Sensitivity | 90dB 1m/2.83Vrms (APUi50C connected) |
Frequency Response | 65Hz - 20kHz (±6db) mounted in Backbox CV345 |
Electrical Connection | Blue butt-splice crimp terminals (14-16 AWG) |
Dimensions | 345mm x 450mm x 33mm (135/8” x 173/4” x 15/16”) |
Product Weight | 1.24Kg (2lbs 12oz) |
Fixing Requirements | BackboxCV345 |
In-line Protection unit | APUi50C |
Rack-Mount Protection Unit | APU-RS8iC or APU-RS16iC |
Warranty | 10 Years Residential (5 Years Commercial) |
Datasheet | Edge5 Datasheet |
Datasheet | Install Guide | Images | CAD |
Edge5 Datasheet | Edge Install Guide | Edge5 Front | Edge5 DWG |
Edge5 Rear |
Edge 3
Inside Edge3
Building on the award-winning Edge Series design, the Edge3 has been repackaged into a smaller footprint allowing installation where there is reduced stud spacing. Using the same tapered perimeter glass resin core as the Edge5 and Edge7, and incorporating OptiDamping and Reduced-Resonance Exciter technology, Edge3 is a plaster up-to design that provides high performance at an entry level price point.
The Edge Soundboard
The speaker uses a high quality fire-resistant panel material which allows for seamless integration into plasterboard walls and ceilings without the need for a full wet skim, all in the easy to install, lightweight form-factor that Amina is known for.
Amina Tip:
Edge Series speakers are designed to be installed into walls and ceilings where there is to be no wet plaster skim, however it is still possible to install the speaker where there are such finishes, but please note that you will need to install the speaker post-plastering and use alignment shims to achieve the correct finish.
Support Products
The Backbox CV300 creates an acoustically tuned and consistent cavity behind the speaker, helping to ensure both consistent audio quality as well as minimising rearward airborne sound transmission.
All new slim-line design, giving reliable speaker protection for life-time worry free performance, in a unit that can be conveniently dressed back with any cable management system or sit neatly behind the rack. Please note that Edge speakers require the ‘C’ variant single channel protection unit – for example for Edge3, use APUi30C.
Both 8-channel and 16-channel passive rack-mounted protection units are available for Edge Series Loudspeakers. For use in installations with higher numbers of low-impedance speakers with a centralised AV rack. Direct-to-PCB screw terminal-blocks allow for fast and easy permanent installation. Please note that Edge speakers require the ‘C’ variant of protection unit, for example APU-RS16iC.
Specification | Edge3 |
Nominal Impedance | 8 Ohms |
Power Handling | 30W/60W |
Sensitivity | 86dB 1m/2.83Vrms (APUi50C connected) |
Frequency Response | 90Hz - 24kHz (±6db) mounted in Backbox CV300 |
Electrical Connection | Blue butt-splice crimp terminals (14-16 AWG) |
Dimensions | 300mm x 400mm x 55mm (134/5” x 153/4” x 13/5”) |
Product Weight | 0.97Kg (2lbs 2oz) |
Fixing Requirements | BackboxCV300 |
In-line Protection unit | APUi30C |
Rack-Mount Protection Unit | APU-RS8iC or APU-RS16iC |
Warranty | 10 Years Residential (5 Years Commercial) |
Datasheet | Edge3 Datasheet |
Datasheet | Install Guide | Images | CAD |
Edge3 Datasheet | Edge Install Guide | Edge3 Front | Coming soon |
Edge3 Rear |